| Plums of a cooling liquid |
| 1. Uncover a broad tank. For this purpose turn a cover counter-clockwise before the first fixing, wait, residual pressure in cooling system will not act in film yet, then press a cover downwards and in this position turn counter-clockwise before the second fixing and definitively uncover. |
| 2. Remove a mudguard under a motor compartment and establish the container under a radiator on the left side. |
|
|
3. Ослабьте a drain stopper on a radiator also give the chance to flow down a cooling liquid in the container. If necessary it is possible to put to a drain aperture (2) piece (1) corresponding pipes for a direction of a stream plum of a cooling liquid. |
|
4. For acceleration plum of a cooling liquid open screws (are specified by an arrow) removals of air from cooling system. Screws are located in connecting муфте a heater hose on a partition of a motor compartment and above thermostat cases. On some models the screw of removal of air can be on the left top party of a radiator. |
| 5. When the stream of the cooling liquid leaving a radiator, will stop, establish the container under a drain stopper of the block of cylinders. On models in volume of 1.6 and 1.8 litres the drain stopper is located on the forward party of the block of cylinders, and on models in volume of 2.0 litres – from the back party of the block of cylinders. |
| 6. Unscrew a drain stopper and give the chance to flow down a cooling liquid from the block of cylinders. |
| 7. After plum of a cooling liquid screw up stoppers of a radiator and on the block of cylinders. |
| Washing of system of cooling |
| 8. Cooling liquid should be changed periodically, and cooling system to wash out, since in system channels the rust and a dirt is formed. Радатор it is necessary to wash out irrespective of the engine. |
| Radiator washing |
| 9. To wash out a radiator, it is necessary to press a target branch pipe of a radiator and to open the screw plum of a cooling liquid. |
| 10. Remove hoses of system of cooling from a radiator. |
| 11. Insert a hose into an entrance aperture of the top tank of a radiator, include water and wash out a radiator before occurrence at its finest from the bottom tank of a radiator. |
| 12. If it is not possible to wash out a radiator pure water take advantage of a washing-up liquid. |
| Engine washing |
| 13. For engine washing unscrew a drain stopper of the block of cylinders, screws of removal of air and remove the thermostat. |
| 14. Disconnect system hoses охдаждения from a radiator and submit through a hose a stream at its finest to the block of cylinders of the engine and wash out it before occurrence from the bottom hose going to a radiator, at its finest. |
| 15. Establish the thermostat and connect hoses of system of cooling. |
| Filling of system of cooling |
| 16. Before filling of system of cooling make sure that all hoses and collars in a good condition. Pay attention that the mix of antifreezes should be used all year long for corrosion prevention. Also check up, that a stopper on a radiator and drain stoppers of the block of cylinders have been established into place. |
| 17. Снимимте a stopper from a broad tank. |
| 18. Unscrew screws of removal of air from cooling system. |
|
19. Establish the additional tank (it is specified by an arrow) in a broad tank and slowly to fill system. The additional tank on a broad tank and slowly to fill system. The additional tank should be established on a broad tank tightly that will provide filling of the highest points of system of cooling. |
| 20. In process of filling of system of cooling with a liquid as soon as there is a coolant, free from air bubbles, from under the screw of removal of air, gradually, since the bottom screws, screw up screws. The additional tank should be full during all process of filling of system. |
| 21. After filling of system of cooling tighten all screws and установитье a stopper on a broad tank. |
| 22. Start the engine and warm up it to working temperature then check up level of a cooling liquid and if necessary finish it to norm. |