Peugeot 406

Since 1996 of release

Repair and car operation


Peugeot 406
+ 1. The maintenance instruction
- 2. Maintenance service
   - 2.1. Petrol models
      2.1.1. Technical data
      2.1.2. Periodicity of service
      - 2.1.3. Maintenance service
         - 2.1.3.1. Each 15000 km or 12 months
            2.1.3.1.1. Replacement of oil and the oil filter
            2.1.3.1.2. Check of level of oil in an automatic transmission
            2.1.3.1.3. Check of tightness of hoses and вытекания liquids
            2.1.3.1.4. Replacement of the filter thin очитки air in ventilation system
            2.1.3.1.5. Check of work of coupling
            2.1.3.1.6. Check of a protective cover of a power shaft
            2.1.3.1.7. A steering and a suspension bracket
            2.1.3.1.8. Shock-absorber check
         + 2.1.3.2. Each 30 000 km
         + 2.1.3.3. Each 60000 km
         + 2.1.3.4. Each 120000 km or alternate years
   + 2.2. Diesel models
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions



2.1.3.1. Each 15000 km or 12 months

2.1.3.1.1. Replacement of oil and the oil filter
THE GENERAL DATA

Periodic replacements of oil and the filter – the most important preventive procedures of servicing. When engine oil grows old, it becomes liquid and polluted that conducts to premature deterioration of the engine.

Before the beginning of this procedure gather all necessary tools and materials. It is necessary, that the engine was warm that oil flew down together with a great bulk of the substances which have polluted it is better.

PERFORMANCE ORDER
1. Ослабьте a drain stopper approximately on a half-turn, using a special key of square section. Place the container for oil plum under a drain stopper and unscrew a stopper completely. If it is necessary, press a stopper when unscrew that oil did not proceed prematurely. Remove ring consolidation from a drain stopper.
2. When oil completely will flow down, wipe all round a drain aperture a rag and reliably screw up a stopper.
3. Use the special tool to weaken the filter, then unscrew his hand. Pour out old oil in the container.
4. Wipe all traces of oil and a dirt round a place of fastening of the filter. Check up, whether there was a rubber consolidation on the block of cylinders. If it remains, remove it.
5. Grease with a thin layer of engine oil rubber consolidation of the new oil filter and screw up the filter a hand, without using any tools.
6. Put the car on an equal horizontal surface.
7. Take щуп for measurement of level of oil, unscrew a cover from a jellied mouth. Fill in oil, using a corresponding grade of oil. Fill in half of necessary quantity of oil and wait for several minutes that oil has flown down in the pallet. Then continue to pour oil in the small portions while level of oil will not reach a minimum level on щупе. At addition about 1st litre oil level will rise to maximum on щупе. Close a cover of a jellied mouth.
8. Start the engine and allow to it to work some minutes. Check up it about leaks of oil round the filter and a drain stopper on the pallet. Keep in mind that the emergency bulb of pressure of oil can burn some seconds as oil should fill all channels and oil capacities in the engine.
9. Switch off the engine and wait some minutes that oil has flown down in the pallet. Check up level of oil and add, if it is necessary.