Peugeot 406

Since 1996 of release

Repair and car operation


Peugeot 406
+ 1. The maintenance instruction
- 2. Maintenance service
   + 2.1. Petrol models
   - 2.2. Diesel models
      2.2.1. Technical data
      2.2.2. Periodicity of service
      - 2.2.3. Maintenance service
         + 2.2.3.1. Each 10000 km or 12 months
         2.2.3.2. Each 20 000 km
         2.2.3.3. Each 30 000 km
         - 2.2.3.4. Each 60 000 km
            2.2.3.4.1. Check of level of oil in a transmission
            2.2.3.4.2. Auxiliary приводной a belt
         2.2.3.5. Each 120 000 km or 2 years
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions



2.2.3.4.2. Auxiliary приводной a belt
THE GENERAL DATA

The mechanism of a tension auxiliary приводного a belt (model with the conditioner)

 1. The bent 7,0 mm a square core

2. A square aperture on the forward party of a tension pulley with the clown

3. A bolt with the clown of fastening of a tension pulley

4. 8,0 mm an aperture for installation of the adaptation of an automatic tension of a belt

Removal, installation and tension check приводного a belt is made the same as and at cars with petrol engines, except for cars with the conditioner.

Removal, installation and adjustment of a tension auxiliary приводного a belt (model with the conditioner)

PERFORMANCE ORDER
Removal
1. Disconnect the negative plug from the accumulator.
2. Tighten a manual brake and lift a forward part of the car. Remove the right forward wheel.
3. Unscrew screws, disconnect скобы and remove a protective arch from under the right forward wing for access reception to a bolt of a pulley of a cranked shaft. If necessary remove a forward mudguard.
4. Ослабьте a bolt of fastening of the clown of a tension pulley (fig. the Mechanism of a tension auxiliary приводного a belt (model with the conditioner see)).
5. Insert the bent 7,0 mm a square core into a square aperture of the clown of the mechanism of a tension.
6. Using a core, turn эксцентриковый the mechanism of a tension before combination of apertures in an arm of a pulley of the mechanism of a tension and in a suspension bracket behind an arm. After combination of apertures establish in them a corresponding core (bolt М8 or a core in diameter of 8 mm).
7. With the fixed mechanism of a tension turn the clown before full easing of a belt. Remove a belt.
Installation and tension
8. Establish приводной a belt round pulleys in a following order:
      – The conditioner compressor;
      – коленвал;
      – A pulley of the mechanism of a tension;
      – The pump of the amplifier of a steering;
      – The alternating current generator;
      – эксцентриковый a pulley of the mechanism of a tension.
9. Check up correctness of installation of a belt on pulleys.
10. Turn эксцентриковый a pulley of the mechanism of a tension to приводному to a belt, it is not removed yet фиксакция. Without changing position эксцентрикового a pulley of the mechanism, tension tighten a fastening bolt.
11. Remove a bolt of fixing of an arm and turn коленвал on four turns in a direction of its working rotation.
12. Check up соосность apertures in an arm of the mechanism of a tension and an installation suspension bracket, repeatedly inserting a bolt.
13. Connect a negative wire to the accumulator, establish an arch of a wheel and a mudguard. Establish a wheel and lower the car.