Peugeot 406

Since 1996 of release

Repair and car operation


Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
- 12. A body
   12.1. The general information
   12.2. Care of a body
   12.3. Care of an upholstery and rugs
   12.4. Repair of insignificant damages of a body
   12.5. Repair of strong damages of a body
   12.6. A forward bumper
   12.7. A back bumper
   12.8. A cowl
   12.9. A cable of the lock of a cowl
   12.10. The cowl lock
   12.11. Doors
   12.12. A door upholstery
   12.13. The lock and handles of opening of a door
   12.14. Glasses of doors
   12.15. A luggage carrier cover
   12.16. The luggage carrier lock
   12.17. A back door
   12.18. The lock of a back door
   12.19. System of the central blocking
   12.20. Electric стеклоподъемники
   12.21. External rear-view mirrors
   12.22. Front and back has flown down
   12.23. The hatch
   12.24. Overlays and emblems
   12.25. Seats
   12.26. The mechanism of a tension of a seat belt of a forward seat
   12.27. Seat belts
   12.28. Salon furnish
   12.29. The central console
   12.30. The panel of devices
+ 13. An electric equipment
+ 14. The basic malfunctions



12.30. The panel of devices Removal

PERFORMANCE ORDER
1. Remove the central console.
2. Remove knots and elements in the following sequence:
      – A combination of devices;
      – The central panel and switches from outside the driver;
      – A radio receiver;
      – Hours;
      – Dynamics of the panel of devices;
      – A pillow of safety of the driver and its contact;
      – The screen wiper engine.
3. Remove a steering column.
4. Unscrew screws of fastening of the panel of a heater and remove it from the panel of devices.
5. Unscrew nuts of fastening of a plate of installation of an electric socket.
6. Remove a plate of installation of a socket of electroconducting of the panel of devices from an arm.
7. Unscrew top (are specified by arrows in a photo at the left) and bottom (are specified by arrows in a photo on the right) bolts of fastening of a rack of support of the panel of devices from outside the driver.
8. Remove a rack of support of the panel of devices from outside the driver.
9. Unscrew 2 screws of fastening of a casing of a heater to the panel of devices.
10. Uncover a ware box. By means of a screw-driver remove the switch (a photo at the left) and a bulb (a photo on the right) illuminations of a ware box and disconnect from them an electric socket.
11. On cars with the conditioner remove the gauge from the top central part of the panel of devices.
12. Remove from the gauge an installation plate so that the gauge could pass through an aperture in the panel of devices.
13. By means of a screw-driver remove lateral заглушку panels of devices from outside the passenger.
14. From a motor compartment unscrew nuts and bolts (are specified by arrows), крепящие a suspension bracket of installation of the panel of devices to a partition of a motor compartment.
15. In car salon unscrew bolts of fastening of the left and right end of the panel of devices to an installation suspension bracket.
16. Being careful, remove the panel from a partition of a motor compartment.

Installation

PERFORMANCE ORDER
Installation is made in sequence, return to removal. Check up, that tubes of giving of air from a heater were correctly combined with a heater. Before fastening of the panel of devices by nuts and bolts check up that all electric sockets are visible through corresponding apertures in the panel of devices. Connect the accumulator and check up that all electric elements and switches work normally.