Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
- 5. Fuel system
   - 5.1. The power supply system of petrol engines
      5.1.1. Technical data
      5.1.2. The air filter and inlet channels
      5.1.3. An accelerator cable
      5.1.4. An accelerator pedal
      5.1.5. System of injection of fuel
      5.1.6. Pressure removal in fuel system
      5.1.7. The fuel pump
      5.1.8. A fuel tank
      5.1.9. Check of fuel system
      5.1.10. The case throttle заслонки
      5.1.11. System of injection Bosch Motronic MP511
      5.1.12. System of injection Magneti Marelli 8P
      5.1.13. An inlet collector
      5.1.14. A final collector
      5.1.15. System of release of the fulfilled gases
   + 5.2. Fuel system of diesel engines
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions



5.1.12. System of injection Magneti Marelli 8P

FUEL ATOMIZERS

Removal

PERFORMANCE ORDER
1. Disconnect the negative plug of the accumulator.
2. Remove the air filter.
3. Unscrew two bolts of fastening of an arm of wires to the top part of a collector.
4. Remove electric sockets from atomizers.
5. Unscrew bolts and remove plates of fastening of atomizers. Atomizers № 1 and 2 fasten one plate, and № 3 and 4 another.
6. Take atomizers and remove from them sealing rings of round section. At installation of atomizers on a former place establish new sealing rings on each atomizer. Grease sealing rings with engine oil for simplification of installation of atomizers.

Installation

PERFORMANCE ORDER
1. Establish atomizers into place and fix their plates. Connect to atomizers electric sockets.
2. Establish an arm of wires to the top part of a collector and screw bolts.
3. Establish the air filter and connect the accumulator. Start the engine and check up atomizers on tightness.

REGULATOR OF PRESSURE OF FUEL

Removal

PERFORMANCE ORDER
1. Disconnect the negative plug of the accumulator.
2. Disconnect a vacuum tube from a regulator.
3. Having enclosed pure rags under a regulator, ослабьте a collar also take a fuel regulator from a highway.

Installation

Installation is made in sequence, return to removal.

POTENTIOMETER THROTTLE ЗАСЛОНКИ

The potentiometer throttle заслонки is established sideways cases of throttles.

Removal

PERFORMANCE ORDER
1. Ослабьте скобу also remove an electric socket from a potentiometer.
2. Unscrew two screws and remove a potentiometer from an axis throttle заслонки.

Installation

Installation is made in sequence, return to removal.

THE ELECTRONIC CONTROL DEVICE (ECU)

ECU it is located in a plastic box which is established on a forward right longeron.

Cнятие

PERFORMANCE ORDER
1. Before removal of a cover of a box of block ECU check up that ignition is switched off. On models with an automatic transmission is available two blocks ECU in a box. The block operating the power supply system and ignition, is located more close to the engine.
2. Disconnect an electric socket, preliminary having lifted upwards the lock lever in the top part of a socket. Remove a socket from a back part, disconnect a forward part and remove block ECU from pins.
3. Lift block ECU upwards and take from the car.

Installation

Installation is made in sequence, return to removal.

THE ENGINE OF MANAGEMENT OF THE IDLING MODE

The engine of management is located by an idling mode sideways cases of throttles.

Removal

PERFORMANCE ORDER
1. Release скобу and remove a socket from the engine.
2. Unscrew two screws and remove the engine of management of an idling mode.

Installation

Installation is made in sequence, return to removal.

THE GAUGE OF ABSOLUTE PRESSURE IN THE COLLECTOR

The gauge is located on an inlet collector.

Removal

PERFORMANCE ORDER
1. Remove an electric socket and a vacuum hose.
2. Remove the gauge from a collector.

Installation

Installation is made in sequence, return to removal.

THE GAUGE OF TEMPERATURE OF ARRIVING AIR

The gauge of temperature of arriving air is located in the case of throttles.

Cнятие

PERFORMANCE ORDER
1. Before gauge removal remove a potentiometer of position throttle заслонки.
2. Release скобу and remove an electric socket from the temperature gauge.
3. Unscrew the screw of fastening of the gauge and take the gauge from the case of throttles.
4. Check up a sealing ring of round section of the gauge and if necessary replace.

Installation

Installation is made in sequence, return to removal.

THE GAUGE OF POSITION КОЛЕНВАЛА

The position gauge коленвала is located on a face sheet картера couplings.

Removal

PERFORMANCE ORDER
1. Track electroconducting from the gauge to a connector of electroconducting and disconnect it from the main plait.
2. Unscrew a bolt of fastening and by means of the lever take the gauge from a rubber condensing ring.

Installation

Installation is made in sequence, return to removal.

SYSTEM ECU RELAY

Block ECU relay is located in a plastic box which is established on a forward right longeron.

Removal

PERFORMANCE ORDER
1. Check up that ignition is switched off, and uncover boxes.
2. Disconnect an electric socket and remove the relay from an installation plate.

Installation

Installation is made in sequence, return to removal.

THE GAUGE OF SPEED OF THE CAR

The gauge of speed of the car – an integral part of a drive of a speedometer.