Peugeot 406

Since 1996 of release

Repair and car operation


Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
- 10. Brake system
   10.1. Technical data
   10.2. Prorolling of hydraulic brake system
   10.3. Brake pipelines and hoses
   10.4. Replacement of lobbies brake колодок
   10.5. Replacement back brake колодок
   10.6. Replacement back brake колодок on drum-type brakes
   10.7. A forward brake disk
   10.8. A back brake disk
   10.9. A back brake drum
   10.10. A support of a forward brake
   10.11. A support of a back wheel
   10.12. The back brake cylinder
   10.13. The main brake cylinder
   10.14. A brake pedal
   10.15. The vacuum amplifier of brakes
   10.16. The unilateral valve of the vacuum amplifier of brakes
   10.17. Adjustment of a manual brake
   10.18. The lever of a manual brake
   10.19. A cable of a manual brake
   10.20. Brake колодки a manual brake (model with disk brakes)
   10.21. The valve of adjustment of pressure in brake system
   10.22. The stoplight switch
   10.23. Antiblocking system of brakes (ABS)
   10.24. The vacuum pump (cars with the diesel engine)
   10.25. Check of the vacuum pump on cars with diesel engines
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions



10.13. The main brake cylinder

Removal

PERFORMANCE ORDER
1. On some models for access improvement lift the receiver air givings to the air filter.
2. Remove a stopper from a tank of the main brake cylinder, the filter and pump out a liquid from a tank. Disconnect an electric socket from the gauge of level of a brake liquid.
3. Remove скобу fastenings and take from a tank with a brake liquid a fastening pin. Remove a tank from the main brake cylinder and take sealing rings from windows of the main brake cylinder. If sealing rings have defects, it is necessary to replace them.
4. Clear a dirt of junctions of brake tubes to the main brake cylinder, enclose rags under places of connections to collect the flowed out brake liquid. Unscrew nuts of fastening of brake tubes to the main brake cylinder.
5. Unscrew 2 nuts of fastening of the main brake cylinder to the vacuum amplifier of brakes. Take the main brake cylinder from a motor compartment.

Repair

Repair of the main brake cylinder can be made only in the presence of the repair complete set of details.

At repair of the main brake cylinder pay attention to an arrangement of all elements repeatedly to establish them on the places.

At assemblage of the main brake cylinder grease all details and sealing rings with a pure brake liquid.

Repair of the main brake cylinder make according to the instruction enclosed to the repair complete set of details.

Installation

PERFORMANCE ORDER
1. Before installation of the main brake cylinder into place check up distance from the end of a pusher of the vacuum amplifier to an interfaced surface of the main brake cylinder which should make 22,3±0,1 mm.
2. Remove all traces of a dirt from interfaced surfaces of the main brake cylinder and the vacuum amplifier of brakes and check up that the sealing ring correct is established in a back part of the main brake cylinder.
3. Establish the main brake cylinder on the vacuum amplifier so that the pusher of the vacuum amplifier has entered into an aperture of the main brake cylinder precisely on the centre. Screw nuts of fastening of the brake cylinder on the vacuum amplifier and tighten their demanded moment.
4. Clear муфты brake tubes and establish them in the main brake cylinder. Screw connecting nuts the demanded moment.
5. Establish sealing rings in windows of the main brake cylinder and establish a tank with a brake liquid on the brake cylinder. Fix a tank a pin and скобой fastenings.
6. Fill a tank with a new brake liquid and remove air from brake system.