Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
- 10. Brake system
10.1. Technical data
10.2. Prorolling of hydraulic brake system
10.3. Brake pipelines and hoses
10.4. Replacement of lobbies brake колодок
10.5. Replacement back brake колодок
10.6. Replacement back brake колодок on drum-type brakes
10.7. A forward brake disk
10.8. A back brake disk
10.9. A back brake drum
10.10. A support of a forward brake
10.11. A support of a back wheel
10.12. The back brake cylinder
10.13. The main brake cylinder
10.14. A brake pedal
10.15. The vacuum amplifier of brakes
10.16. The unilateral valve of the vacuum amplifier of brakes
10.17. Adjustment of a manual brake
10.18. The lever of a manual brake
10.19. A cable of a manual brake
10.20. Brake колодки a manual brake (model with disk brakes)
10.21. The valve of adjustment of pressure in brake system
10.22. The stoplight switch
10.23. Antiblocking system of brakes (ABS)
10.24. The vacuum pump (cars with the diesel engine)
10.25. Check of the vacuum pump on cars with diesel engines
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions
|
Check
| PERFORMANCE ORDER |
| 1. Press a brake pedal some times at the idle engine to create in cavities of the vacuum amplifier identical pressure (close to atmospheric). |
| 2. Simultaneously on the effort put to a pedal, define, whether there is no jamming of the case of the valve. |
| 3. Stop a pedal of a brake in the middle of its course and start the engine. At the serviceable vacuum amplifier the pedal of a brake after engine start-up should leave forward. If the pedal does not leave forward, check up fastening of a tip of a hose, a condition of fastening of a flange of a tip in the amplifier, a hose and union condition. |
| 4. On cars with diesel engines check up also working capacity of the vacuum pump. |
|
Removal
| PERFORMANCE ORDER |
| 1. Remove the main brake cylinder. |
| 2. Ослабьте a collar also disconnect a vacuum hose from the unilateral valve of the vacuum amplifier of brakes. In car salon uncover boxes with fuses. |
| 3. Disconnect an electric socket from key колодки, unscrew screws of fastening and remove the bottom furnish of the panel of devices. Remove скобу fastenings and take a pin with a head and an aperture under шплинт, крепящий a pusher of a pedal of a brake to the vacuum amplifier of brakes. |
| 4. Unscrew nuts, крепящие the vacuum amplifier to a partition of a motor compartment, take it. |
|
Installation
| PERFORMANCE ORDER |
| 1. Before installation of the vacuum amplifier measure distance from the end of a pusher of the vacuum amplifier to an interfaced surface of the main brake cylinder which should make 22,3±0,1 mm. |
| 2. Be convinced that the lining is correctly established on a back part of the vacuum amplifier, then establish the vacuum amplifier in a motor compartment. |
| 3. Check up that the pusher is correctly combined with a brake pedal, then screw nuts of fastening of the vacuum amplifier and tighten their demanded moment. |
| 4. Combine a pedal with a pusher, insert a pin with a head and an aperture under шплинт and fix скобами fastenings. Establish the bottom furnish of the panel of devices. |
| 5. Connect a vacuum hose to the unilateral valve and fix a collar. |
| 6. Establish the main brake cylinder and remove air from brake system. |
|
|
|