Peugeot 406

Since 1996 of release

Repair and car operation


Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. The engine
   - 3.1. Petrol engines
      3.1.1. Technical data
      3.1.2. Check of pressure of compression
      3.1.3. Mechanism installation timing
      3.1.4. A cover of a head of the block of cylinders
      3.1.5. A pulley of a cranked shaft
      3.1.6. A casing of a gear belt
      3.1.7. A gear belt
      3.1.8. The mechanism of a tension of a gear belt and pulleys
      3.1.9. Replacement of a sealing ring of a cam-shaft
      3.1.10. A cam-shaft and pushers
      3.1.11. Check and adjustment of backlashes of valves of engines of 1.6 litres
      3.1.12. A head of the block of cylinders
      3.1.13. The oil pallet
      3.1.14. The oil pump
      3.1.15. An oil radiator
      3.1.16. Replacement of consolidations of a cranked shaft
      3.1.17. A flywheel
      3.1.18. A suspension bracket of the power unit
   + 3.2. Diesel engines
   + 3.3. Engine repair
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions



3.1.4. A cover of a head of the block of cylinders Removal
PERFORMANCE ORDER
1. Disconnect the negative plug of the accumulator.
Models with volume of the engine of 1.6 litres
2. Ослабьте collars of fastening also remove hoses of giving of air from the forward right end of a cover of a head.
3. Remove a tubule connecting the air filter and a head of the block. Also remove an inlet branch pipe on the left side of a head cover.
4. Disconnect two скобы and unscrew two screws located in front, and uncover the filter. Take filtering element.
5. In regular intervals and gradually unscrew ten nuts (are specified by arrows) fastenings of a cover of a head of the block of cylinders.
6. Cнимите a cover together with a rubber lining. Check up a lining on presence of defects and, if necessary, replace.
Models with engines in volume of 1.8 and 2.0 litres
7. Remove a fuel highway and fuel atomizers.
8. Remove an electric socket on the left side of the ignition coil, located in the centre of a cover of a head of the block of cylinders. Unscrew six bolts of fastening and remove the ignition coil upwards.
9. Ослабьте collars also remove hoses of giving of air from a forward left-hand side of a forward cover.
10. Consistently, on a spiral, outside inside, gradually ослабьте, and then unscrew and remove bolts of fastening of each cover of a head.
11. Remove head covers together with linings.

Installation

PERFORMANCE ORDER
Models in volume of 1.6 litres
1. Establish a rubber lining in a flute of a cover of a head, guaranteeing its correct arrangement.
2. An external surface of a lining grease with hermetic.
3. Being careful, establish a head cover not to displace a cover lining.
4. Check up correctness of installation of a lining. In regular intervals and gradually, in the specified sequence, tighten nuts of fastening of a cover of a head of the block of cylinders.
5. Establish filtering element of the air filter and its cover. Repeatedly connect hoses of giving of air and the inlet channel. Connect the negative plug of the accumulator.
Models with engines in volume of 1.8 and 2.0 litres
6. Establish a rubber lining in a flute of a cover of a head, guaranteeing its correct arrangement.
7. Being careful, establish a head cover not to displace a cover lining.
8. Check up correctness of installation of a lining. In regular intervals and gradually, in the specified sequence, tighten nuts of fastening of a cover of a head of the block of cylinders.
9. Connect hoses of giving of air to a forward cover of a head and fix their collars.
10. Establish the ignition coil between covers of a head and fix its bolts.
11. Establish a fuel highway and fuel atomizers.
12. Connect a negative wire of the accumulator. Start the engine and check up tightness of connections.