Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. The engine
   + 3.1. Petrol engines
   + 3.2. Diesel engines
   - 3.3. Engine repair
      3.3.1. Technical data
      3.3.2. Removal and engine and transmission installation
      3.3.3. Removal and installation of engines from an automatic transmission
      3.3.4. Engine repair
      3.3.5. Removal and installation of a head of the block of cylinders
      3.3.6. Dismantling of a head of the block of cylinders
      3.3.7. Clearing and survey of a head of the block of cylinders
      3.3.8. Assemblage of a head of the block of cylinders
      3.3.9. Removal of pistons from rods
      3.3.10. Removal коленвала
      3.3.11. The block of cylinders
      3.3.12. Pistons and rods
      3.3.13. Коленвал
      3.3.14. Survey radical and шатунных bearings
      3.3.15. Engine balance of assembly at major repairs
      3.3.16. Installation of piston rings
      + 3.3.17. Installation коленвала and check of working backlashes of radical bearings
      + 3.3.18. Installation of pistons
      3.3.19. Start of the engine after major repairs
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions



3.3.14. Survey radical and шатунных bearings
THE GENERAL DATA

Typical defects of bearings


PERFORMANCE ORDER
1. Even thus that radical and шатунный bearings are subject to replacement at engine major repairs, they are necessary for examining carefully as they can give the valuable information concerning an engine condition.
2. Bearing failure can occur because of a lack of greasing, presence of a dirt or other alien particles, an engine or corrosion overload. Irrespective of the reason of failure of the bearing the reason which has caused an exit of the bearing out of operation before the engine will repeatedly gather should be eliminated.
3. At survey of bearings remove them and spread out in the same order as they have been established on the engine. It will allow to define a corresponding neck коленвала and will facilitate search of malfunctions.
4. Alien particles can get to the engine various ways. Metal particles can is in engine oil as a result of normal deterioration of the engine. Small particles together with engine oil can get to bearings and easily take root into a soft material of the bearing. The big particles, getting to the bearing, will scratch the bearing or a neck коленвала. The best prevention of failure of the bearing for this reason is that: carefully clear all internal surfaces of the engine and keep them clean at engine assemblage. Frequent and regular replacement of oil with the filter Is recommended also.
5. Insufficient greasing of necks коленвала can be caused many different reasons, such as an oil heat, an overload of the engine and oil leak.
6. The manner of driving of the car also influences durability of the bearing. Completely open throttle заслонка at low turns of the engine creates high loading on bearings and expression from a zone of contact of an oil film. These loadings lead to occurrence of cracks in a working part of the bearing that weakens the bearing and can lead to a separation of an antifrictional layer from a steel basis.
7. Movement on short distances leads to corrosion of bearings because the engine does not leave on the stabilised working temperature at which water steams and corrosion gases leave. These steams and gases, being condensed in engine oil, form acid and a deposit. Acid together with engine oil gets to bearings, and corrosion of bearings begins.
8. Wrong selection of bearings at engine assemblage also leads to failure of bearings. The bearings established with a preliminary tightness, leave an insufficient working backlash of the bearing therefore decreases or there is no butter layer for greasing.