Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. The engine
   + 3.1. Petrol engines
   + 3.2. Diesel engines
   - 3.3. Engine repair
      3.3.1. Technical data
      3.3.2. Removal and engine and transmission installation
      3.3.3. Removal and installation of engines from an automatic transmission
      3.3.4. Engine repair
      3.3.5. Removal and installation of a head of the block of cylinders
      3.3.6. Dismantling of a head of the block of cylinders
      3.3.7. Clearing and survey of a head of the block of cylinders
      3.3.8. Assemblage of a head of the block of cylinders
      3.3.9. Removal of pistons from rods
      3.3.10. Removal коленвала
      3.3.11. The block of cylinders
      3.3.12. Pistons and rods
      3.3.13. Коленвал
      3.3.14. Survey radical and шатунных bearings
      3.3.15. Engine balance of assembly at major repairs
      3.3.16. Installation of piston rings
      + 3.3.17. Installation коленвала and check of working backlashes of radical bearings
      - 3.3.18. Installation of pistons
         3.3.18.1. A choice of the loose leaf of the bearing
         3.3.18.2. Check of a working backlash of the loose leaf шатунного the bearing
      3.3.19. Start of the engine after major repairs
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions


лечение спины

3.3.18. Installation of pistons
PERFORMANCE ORDER
1. Check up that шатунные loose leaves are correctly established. If new loose leaves are established, check up that all traces of protective greasing are removed by corresponding solvent. Wipe loose leaves and rods pure безворсовой a fabric.
2. Grease cylinders, pistons and piston rings.
3. Installation of pistons is necessary for beginning with the first cylinder. Check up correctness of an arrangement of piston rings on the piston, then compress their special оправкой.
4. Insert the piston with оправкой, compressing rings, into the top part of the first cylinder. On petrol engines check up that the arrow on the piston bottom is directed to a gear belt of a drive, and on diesel engines dredging on the piston bottom is directed to a forward part of the block of cylinders. Using wooden брусок (the hammer handle) press on the piston and press it together with the piston the cylinder.
5. Check up combination of the bottom head of a rod with a neck коленвала, if necessary tighten the piston a rod and establish the bottom head of a rod with the loose leaf on a neck коленвала.
6. Establish a cover of the bottom head of a rod with the loose leaf and screw up nuts the demanded moment. Pay attention that earlier put marks on a cover of a rod and a rod should be combined.
7. Tighten nuts of fastening of a cover of the bottom head of a rod динамометрическим a key.
8. Tighten nuts of fastening of a cover of the bottom head of a rod on a demanded corner.
9. After a tightening of nuts of covers of bearings turn коленвал. Коленвал should rotate freely. Some effort is required at installation of new loose leaves, but at the same time there should not be jammings or проворачивания a shaft with the appendix of the big efforts.
10. Similarly establish three remained pistons.
11. Establish a head of the block of cylinders and the oil pump.