Peugeot 406

Since 1996 of release

Repair and car operation


Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
- 5. Fuel system
   + 5.1. The power supply system of petrol engines
   - 5.2. Fuel system of diesel engines
      5.2.1. Technical data
      5.2.2. Filling and prorolling of fuel system
      5.2.3. The air filter and air inlet channels
      5.2.4. An accelerator cable
      5.2.5. An accelerator pedal
      5.2.6. Adjustment of the fuel pump of a high pressure
      5.2.7. The electromagnetic valve of a stop of the engine
      5.2.8. The fuel pump of high pressure Bosch
      5.2.9. The fuel pump of high pressure Lucas
      5.2.10. Installation of the moment of injection
      5.2.11. Installation of the moment of injection on ТНВД Bosch
      5.2.12. Installation of the moment of injection on ТНВД Lucas
      5.2.13. Fuel atomizers
      5.2.14. Gauges and executive mechanisms of system Bosch AS3
      5.2.15. Gauges and executive mechanisms (Lucas EPIC)
      5.2.16. An inlet collector
      5.2.17. A final collector
      5.2.18. Турбонагнетатель
      5.2.19. Removal and installation турбонагнетателя
      5.2.20. Check турбонагнетателя
      5.2.21. An intermediate cooler
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions



5.2.9. The fuel pump of high pressure Lucas
THE GENERAL DATA
The prevention

Be cautious, that the dirt has not got to the fuel pump or the high pressure pipeline at work on the fuel pump. Also always it is necessary to use new consolidation.

Removal

PERFORMANCE ORDER
1. Disconnect the negative plug of the accumulator.
2. Remove the electronic control device of system of injection of fuel (ECU) and block ECU box.
3. Remove system of inlet pipes and the top part of an inlet collector.
4. Remove auxiliary приводной a belt.
5. Remove the alternating current generator.
6. Unscrew bolts and remove an intermediate arm (the pump of the amplifier of a steering and the generator) sideways the block of cylinders.
7. Unscrew bolts of fastening of a plait of wires to the engine and move a fixing element aside from the fuel pump. Probably, it is necessary to disconnect some electric sockets to move a plait of wires on sufficient distance. Mark all disconnected sockets.
8. Remove a casing of a gear belt of the drive, closing pulley of the fuel pump.
9. Unscrew submitting and returnable fuel hoses from the pump. Close the open ends of hoses corresponding stoppers.
10. Disconnect electric wires from the pump and collars of fastening of hoses.
11. Unscrew nuts of fastening of pipes of atomizers to the fuel pump.
12. For a pulley коленвала turn коленвал in a direction of rotation of the engine while two apertures under a bolt in a pulley of the fuel pump of a high pressure will not be combined with corresponding to apertures in the engine. The engine will be easier for turning if to unscrew candles накаливания.
13. Insert two bolts M8 through apertures in a pulley of the fuel pump. These bolts will keep a pulley when the fuel pump of a high pressure will be removed, thus, it is not necessary to remove a gear belt of a drive.
14. Note position of the fuel pump of a high pressure concerning an installation suspension bracket, using чертилку or a felt-tip pen (the label is specified by an arrow). It will guarantee that the moment of injection of fuel will be kept at installation on a former place.
15. Unscrew three forward nuts (arrow) of fastening of the pump.
16. Unscrew and remove a back nut and a bolt (are specified by an arrow), marking an arrangement of washers, and support the fuel pump on a bar.
17. Separate a pulley of the fuel pump from a pump shaft.
18. Being careful, remove the pump.

Installation

PERFORMANCE ORDER
1. Establish into place segment шпонку on a pump shaft.
2. Establish the pump into place and support on a bar, as in the course of removal.
3. Establish a pulley on a shaft of the fuel pump.
4. Combine the labels made on the pump and a suspension bracket of installation before removal. Establish and slightly tighten nuts and a bolt of fastening of the pump.
5. Establish the moment of injection of the fuel pump.
6. Establish and repeatedly tighten the pipelines connecting the fuel pump with atomizers.
7. Connect submitting and returnable fuel hoses.
8. Connect a cable of the increased turns of idling to the pump lever.
9. Establish a casing of a gear belt of a drive.
10. Establish a fixing element of a plait of wires to the engine and repeatedly connect earlier disconnected sockets.
11. Establish an intermediate arm to the block of cylinders.
12. Establish the alternating current generator, the pump of the amplifier of a steering and auxiliary приводной a belt.
13. Establish the top part of an inlet collector.
14. Establish a box of block ECU and block ECU.
15. Connect the negative plug of the accumulator.
16. Remove air from fuel system.