Peugeot 406

Since 1996 of release

Repair and car operation

Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
- 11. A suspension bracket and a steering
   11.1. Technical data
   11.2. Rotary fists
   11.3. Replacement of forward bearings of a nave
   11.4. A forward rack
   11.5. Repair of a forward rack
   11.6. The bottom lever of a forward suspension bracket
   11.7. The bottom spherical hinge of a forward suspension bracket
   11.8. The stabilizer of cross-section stability of a forward suspension bracket
   11.9. A side scene of the stabilizer of cross-section stability of a forward suspension bracket
   11.10. The bottom frame of a forward suspension bracket
   11.11. A nave of a back wheel
   11.12. Replacement of bearings of a back nave
   11.13. The shock-absorber of a back suspension bracket
   11.14. A cylindrical spring of a back suspension bracket
   11.15. A pin of a nave of a back suspension bracket
   11.16. The bottom lever of a back suspension bracket
   11.17. The top lever of a back suspension bracket
   11.18. The directing lever of a back suspension bracket
   11.19. Draught of a back suspension bracket
   11.20. The stabilizer of cross-section stability of a back suspension bracket
   11.21. A side scene of the stabilizer of cross-section stability of a back suspension bracket
   11.22. A steering wheel
   11.23. A steering column
   11.24. An intermediate shaft of a steering column
   11.25. The ignition lock
   11.26. The steering mechanism
   11.27. Replacement of protective covers of the steering mechanism
   11.28. Removal of air from system of a steering with the amplifier
   11.29. The pump of the amplifier of a steering
   11.30. The spherical hinge of steering draught
   11.31. Steering draught
   11.32. Corners of installation of wheels
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

11.15. A pin of a nave of a back suspension bracket
Removal

PERFORMANCE ORDER

1. Lift a back part of the car and fix on supports. Remove a corresponding back wheel.

2. On cars with ABS unscrew a bolt of fastening of the gauge established on a wheel, and take it from a pin.

3. Remove a back nave of a wheel.

4. Using a G-shaped clip, press a brake hose in a place closest to the working brake cylinder.

5. Clear traces of a dirt round connection of a brake tube to the working brake cylinder. Unscrew a connecting nut and take a brake tube from the brake cylinder.

6. Disconnect a cable of a drive of a manual brake. Unscrew 4 bolts of fastening of a brake board in gathering to a pin and remove a board from the car.

7. Establish a jack under the external end of the bottom lever and lift a jack so that the back spring was slightly compressed.

8. Unscrew a nut and release a side scene of the stabilizer of cross-section stability from a pin.

9. Unscrew a nut and remove the spherical hinge of the directing lever from a rotary pin.

10. Unscrew bolts and nuts of fastening of external hinges of the bottom and top lever.

11. Unscrew a nut and take a bolt of fastening of bent for to a pin. Remove a pin from the car.

12. Check up a condition of a pin and, in the presence of defects, replace it.

Installation

PERFORMANCE ORDER

1. At pin installation it is necessary to use only new nuts. Grease шарнирные bolts and surfaces of contact of a suspension bracket with nuts universal lubricant Molykote Q Rapide Plus.

2. Establish a pin into place, insert external шарнирные bolts of fastening of a pin to the top and bottom lever and a draught bolt. Screw a hand on bolts new nuts.

3. Establish a side scene of the stabilizer of cross-section stability and the spherical hinge of the directing lever. Fix new nuts, tightening their demanded moment.

4. Establish a brake board in gathering on a pin and tighten bolts of fastening of a board the demanded moment.

5. Establish a nave on a pin.

6. Connect a brake pipe to the working brake cylinder and tighten a nut of fastening by the demanded moment. Remove a clip from a brake hose and remove air from brake system.

7. On models with ABS establish the gauge of rotation of a wheel on a rotary pin.

8. Establish a back wheel and lower the car. Shake the car that all elements of a suspension bracket have risen on the places. Tighten nuts of fastening top both bottom шарнирных bolts and a bolt of fastening of draught the demanded moment.